Not sure how to disassemble the Bissell Crosswave? Well, is not as hard as you might. You will need a screwdriver or even a pen. Insert it right into the opening part that is right above the water tank, which is one the back of the machine. Next, you will need to pull the handle while pushing the screwdriver or pen into opening, which should be circular. Once you’ve removed it, then you can insert the handle again until it clicks in place.

Silky Terrier Dog Breed Playing Aro...

To view this video please enable JavaScript, and consider upgrading to a web browser that supports HTML5 video

Silky Terrier Dog Breed Playing Around

Can you remove the handle on a Bissell CrossWave?

The CrossWave’s handle snaps into place with a spring-loaded button once it is inserted into the machine. The button must be pressed again in order to free the handle from the machine.

How do you take the handle off a Tineco?

To remove the handle, use a tool (such as a screwdriver) to press the spring and then lift the handle out of the appliance. Be sure to fully charge the device (4+0.5 hours; see “Charging Instructions”) before the first use. 

Why did my Bissell CrossWave stop working?

You may have encountered a problem with your CrossWave brush while cleaning. There’s a good chance there’s an impediment. To reset the brush, unplug your machine.

Why does my Bissell CrossWave leak water?

If the side vents of the machine are dripping:In order to avoid a buildup of foam, use the recommended amount of formula on the clean tank, which is clearly marked. Use the correct CrossWave formula as well (not portable or upright cleaning formulas)

Why does my Bissell CrossWave stop spinning?

Debris that was preventing the machine from working should be removed. Check for hair or debris at the ends of brush rolls and brush equipment. Reinstall the Brush Roll and Brush Roll Window after removing any remaining hair or debris.

Why is my Bissell Crosswave leaving dirty streaks?

When cleaning, you may not be using enough new cleaning solution. If you want a smooth finish, hold the trigger down. Using too much water during passes can also cause streaking. Release the trigger after you’ve made a few wet passes to avoid spraying the wet area.

How do I get my Bissell Crosswave to self clean?

The self-cleaning cycle can be started by pressing the button on the front of the machine. Empty the dirty water tank if it fills up during the cycle. Whenever the machine shuts off and the digital display shows an empty water tank icon, you know it’s full.

How often do you change the filter on the Bissell Crosswave?

Replace the filter and brush on your Bissell Crosswave vacuum if it’s losing suction power. The Crosswave’s filter and brush should be replaced every three to four months.

How do you clean a Tineco a10 filter?

Unscrew the filters by turning them counter-clockwise. Under running water, wash the dustbin and the mesh filter. Before reinstalling the dustbin and mesh filter, they should be air dried thoroughly. Use the Tineco Pre Filter Cleaning Tool to clean the pre filter.

Can I return my BISSELL crosswave to Walmart?

As long as it’s within 90 days of purchase, yes, you can return a used or defective vacuum cleaner to Walmart (including Hoover, Dyson, iRobot, Shark, Bissell, and so on) (including a receipt and original packaging).

Can I return my BISSELL crosswave to Kohl’s?

Yes, they will accept most returns for 180 days after the original purchase date.

How long is BISSELL crosswave warranty?

Two-Year Limited WarrantyBISSELL has the final say. Two years after the original purchase date, any defective or manufacturing part is covered for free. 

Can you replace the battery in the Bissell CrossWave?

 Authorized Service Center can replace the battery if it is needed and is covered by the manufacturer warranty. It’s not possible for consumers to buy and install a replacement battery from just anywhere.

Do you have to clean Bissell crosswave after every use?

After each cleaning session, be sure to empty the dirty water tank and refill it. Even though it is possible, we do not recommend leaving the dirty water unattended for an extended period of time. Your vacuum may become contaminated with the foul water.

Can you use Lysol in CrossWave?

It is not recommended that you use Lysol in the CrossWave clean tank.

What can I use instead of Bissell cleaning formula?

There are many Bissell owners who make their own carpet shampoo by mixing laundry detergent (without bleach), liquid softener (without bleach), ammonia (without bleach), and water (one gallon). In a large jug, keep the mixture. This is enough for a few cleanings..

Can I use the CrossWave on laminate flooring?

You can vacuum and wash your laminate floors and area rugs all at once if you have a CrossWave®.

ncG1vNJzZmijqaG8r7zOsJylpF6YvK57x6iuZqyfYrGqv8Csqp6lkqGybq7IrKqepJxisLO70qyumq6VZA%3D%3D